Welcome, Guest

GPZ900R Petrol Tap Kit ........QUESTION ?

Welcome to the Kunena forum!

Tell us and our members who you are, what you like and why you became a member of this site.
We welcome all new members and hope to see you around a lot!

Page:
1
2

TOPIC:

GPZ900R Petrol Tap Kit ........QUESTION ? 10 years 8 months ago #2348

strate6
Topic Author
Offline
Platinum Member
On An Adventure Before Dementia ! !
Posts: 1149
Thank you received: 356

For those who have carried our the GPZ (ZX)900R Petrol Tap Conversion, can you please help me ?

When I bought the tap, I stripped it to make sure all was well inside & it looked ok but once I tried using it, there was a leak from around the flap that selects ON/PRI/RES. It must be the large o ring that sits in the recess on the flap.
Judging by the condition of the screw heads & internals & believe this tap has not been opened up before & was from a low mileage bike.

No problem.........I just bought a kit online.
This is shown below.

Problem is I cannot find where the TWO large o rings supplied actually go.
ONE of them obviously fits in the recess, but I cannot work out what the other is for as my tap ONLY has one such o ring inside.
Mine is shown below.

A Large Black Seal OK
B Large O Ring for Flap OK
C Thin Wavey Metal Washer (goes between outer face of flap & cover plate with 2 screws.

So can anyone tell me where the OTHER large O Ring goes ??????

Pete F
UK

Why Have Four When You Can Have Six ?

Please Log in or Create an account to join the conversation.

GPZ900R Petrol Tap Kit ........QUESTION ? 10 years 8 months ago #2363

Toddh Offline Platinum Member Posts: 472 Thank you received: 65	Pete: Have you looked at the micro fiche? cdn.partzilla.com/diagram/kawasaki/08/0188/F-12.png Todd. KZ1300 A-4 4TH 1300 IN 30 YEARS KZ1000 D-3/ Z1R ZX900 GPZ A-3 KZ750 E-1 K1200GT CB750F 1978
	Please Log in or Create an account to join the conversation.

GPZ900R Petrol Tap Kit ........QUESTION ? 10 years 8 months ago #2368

strate6 Topic Author Offline Platinum Member On An Adventure Before Dementia ! ! Posts: 1149 Thank you received: 356	Yep................it only shows one o ring on there too !! Pete F Why Have Four When You Can Have Six ?
	Please Log in or Create an account to join the conversation.

GPZ900R Petrol Tap Kit ........QUESTION ? 10 years 8 months ago #2369

KZQ
Offline
Administrator
Lifelong Rider Suffering Through MBD
Posts: 1032
Thank you received: 275

Isn't the other large O ring to be bent into the oval seal groove at the tank?

1947 Indian Chief, 1968 BSA Shooting Star, 1970 BSA 650 Lightning, 1974 Kawasaki W3, 1976 KZ900 A4, 1979 KZ750 B4, 1979 KZ750 B4 Trike, 1980 KZ550, 1981 KZ1300, 1982 KZ1100 Spectre, 1985 Kawasaki ZN1300, 1987 Yamaha Trail Way, 2000 Honda Valkyrie Tourer, 1981 GL 1100, 2009 Yamaha RoadLiner S

The following user(s) said Thank You: strate6

Please Log in or Create an account to join the conversation.

Last edit: by KZQ.

GPZ900R Petrol Tap Kit ........QUESTION ? 10 years 8 months ago #2371

strate6 Topic Author Offline Platinum Member On An Adventure Before Dementia ! ! Posts: 1149 Thank you received: 356	Ahhh, You just maybe right Bill. I guess that would make some sort of sense & be cheaper than making a contoured ring. Will see if it fits that oval groove tomorrow. Thanks again Pete F Why Have Four When You Can Have Six ?
	Please Log in or Create an account to join the conversation.

GPZ900R Petrol Tap Kit ........QUESTION ? 10 years 8 months ago #2373

kwak1261 Offline Platinum Member Posts: 477 Thank you received: 72	Looks very similar to a GS1000 fuel tap. 44mm bolt hole centre you get a shaped oval O ring for the base in a overhaul kit. i have one of these taps so i could take a few measurements if needed. also came with 50mm bolt hole spacing. Ian Z1300 A4 ZG1300 DFI X2 Z1261J GS1000S Vmax1200 XT500 The following user(s) said Thank You: strate6
	Please Log in or Create an account to join the conversation. Last edit: by kwak1261.