kz1300 banner

rear-brake, tech-advise needed

  • BigSix
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
More
3 years 6 months ago #29189 by BigSix
rear-brake, tech-advise needed was created by BigSix
Hi Guys, 
I took the lady out of her slumber and she, after getting fuel started fine. I though noticed at a crossing that she, even with neutral in, does not roll anymore any noticed the rear-brake blocking. The disc hot, so I paused and made it home. With help from a friend we dismounted the rear-master cylinder and noticed the piston was stuck. We have been able to get him moving again, yet the brake shows the identical symptoms, after around 1 mile the disc is hot. Compare to the front-discs too hot I guess. 

What would be your approach ?

Thanks and best regards, 
Holger

Z1300 A1/ KZT30AG built 1979
frame KZT30A 004285
engine KZT30A 000288
location: borderland-triangle France/ Germany/ Switzerland, Europe

Please Log in or Create an account to join the conversation.

More
3 years 6 months ago #29190 by Bucko
Replied by Bucko on topic rear-brake, tech-advise needed
The equalizing port (smaller of the two holes) in your master cylinder is blocked and preventing brake fluid from flowing back into the reservoir when you release the brakes. Use a small wire or toothpick to clear the blockage and flush the fluid.

Hello from Canada's We(s)t coast.

Please Log in or Create an account to join the conversation.

  • BigSix
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
More
3 years 6 months ago - 3 years 6 months ago #29191 by BigSix
Replied by BigSix on topic rear-brake, tech-advise needed
Hey Bucko, thanks. When we dismounted the master-cylinder, we did check if that hole is clean since that was the first idea. It was clean indeed, and at the same time I was able to press one of the pistons back into the caliper. I just ordered myself the below item to see if that will solve it:

Keep your fingers crossed ...
Holger

ebay 172807438951

Z1300 A1/ KZT30AG built 1979
frame KZT30A 004285
engine KZT30A 000288
location: borderland-triangle France/ Germany/ Switzerland, Europe
Last edit: 3 years 6 months ago by BigSix. Reason: looked bad

Please Log in or Create an account to join the conversation.

More
3 years 6 months ago #29195 by Neville
Replied by Neville on topic rear-brake, tech-advise needed
I had the same rear brake problem a number of years ago - however, it was my fault as I adjusted the pedal stop to reduce the free play.  Not logical for this to happen if you had no problems last time you ran your 1300 but worth checking?

Please Log in or Create an account to join the conversation.

  • BigSix
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
More
3 years 6 months ago #29197 by BigSix
Replied by BigSix on topic rear-brake, tech-advise needed

I had the same rear brake problem a number of years ago - however, it was my fault as I adjusted the pedal stop to reduce the free play.  Not logical for this to happen if you had no problems last time you ran your 1300 but worth checking?

Will check that, though I did not change anything in there.
Holger
 

Z1300 A1/ KZT30AG built 1979
frame KZT30A 004285
engine KZT30A 000288
location: borderland-triangle France/ Germany/ Switzerland, Europe

Please Log in or Create an account to join the conversation.

More
3 years 6 months ago #29198 by zed_thirteen
Replied by zed_thirteen on topic rear-brake, tech-advise needed

I had the same rear brake problem a number of years ago - however, it was my fault as I adjusted the pedal stop to reduce the free play.  Not logical for this to happen if you had no problems last time you ran your 1300 but worth checking?

 
I agree - I've done this too.  Noticed an orange glowing rear disk when passing a motorcycle shop window

1980 KZ1300 B2 Touring/A2
1990 ZZ-R1100 C1

Please Log in or Create an account to join the conversation.

Time to create page: 0.129 seconds
Powered by Kunena Forum