kz1300 banner

Oil Level Glass Seal

  • strate6
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
  • On An Adventure Before Dementia ! !
More
4 years 2 weeks ago - 4 years 2 weeks ago #28176 by strate6
Oil Level Glass Seal was created by strate6
Has anyone out there ever removed the Oil Seal and Glass from a Z1300 Clutch Casing and found a sensibly priced replacement oil seal to use ??
My casing is the one from the later (Deep Sump) 6.2L model Z1300 which has a larger glass and oil seal than the earlier (shallow sump) models.

It "looks" to be just a low profile oil seal holding the glass in position as seen in the photo below, but looking at the Genuine Kawasaki Part, its ridiculously expensive.

Any relavent experince appreciated.

Pete F
UK

Why Have Four When You Can Have Six ?
Attachments:
Last edit: 4 years 2 weeks ago by strate6.

Please Log in or Create an account to join the conversation.

More
4 years 2 weeks ago #28179 by Bar
Replied by Bar on topic Oil Level Glass Seal
I order one for the Voyager, I think it is the same one
$37 on partzilla but it was back order
I think I order from ebay or Zed-parts
but it was about the same price

1984 Kawasaki Voyager
2002 Honda CBR954

Please Log in or Create an account to join the conversation.

More
4 years 2 weeks ago #28180 by zed_thirteen
Replied by zed_thirteen on topic Oil Level Glass Seal
I have removed one to clean once when I had the cover off for polishing. I think I used an allen key wrapped slightly with cloth or padding in from the slot behind it and gentle pressure against the rear of the glass at opposite sides around the glass.

To the best of my memory the glass and seal are a single part rather than a seal and glass. I could be wrong and just didn't try hard enough to separate them. The glass was contained within the outer edge of the seal rather than being to the rear of the seal

1980 KZ1300 B2 Touring/A2
1990 ZZ-R1100 C1

Please Log in or Create an account to join the conversation.

  • strate6
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
  • On An Adventure Before Dementia ! !
More
4 years 2 weeks ago #28181 by strate6
Replied by strate6 on topic Oil Level Glass Seal

zed_thirteen wrote: I have removed one to clean once when I had the cover off for polishing. I think I used an allen key wrapped slightly with cloth or padding in from the slot behind it and gentle pressure against the rear of the glass at opposite sides around the glass.

To the best of my memory the glass and seal are a single part rather than a seal and glass. I could be wrong and just didn't try hard enough to separate them. The glass was contained within the outer edge of the seal rather than being to the rear of the seal


Thank for your reply......................did you replace the glass and seal or re-fit the existing one ??

Pete F
UK

Why Have Four When You Can Have Six ?

Please Log in or Create an account to join the conversation.

More
4 years 2 weeks ago #28182 by zed_thirteen
Replied by zed_thirteen on topic Oil Level Glass Seal
Lol, it was late 90's! To be honest I just don't remember but I probably just bought a new one. I remember being worried when I tapped it back into place but it's okay if you go slowly

1980 KZ1300 B2 Touring/A2
1990 ZZ-R1100 C1

Please Log in or Create an account to join the conversation.

  • strate6
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
  • On An Adventure Before Dementia ! !
More
4 years 2 weeks ago #28183 by strate6
Replied by strate6 on topic Oil Level Glass Seal
Thanks for confirming.

I think it will have to be replaced................but at £29 for just a seal with glass is ridiculous !

Pete F
UK

Why Have Four When You Can Have Six ?

Please Log in or Create an account to join the conversation.

Time to create page: 0.134 seconds
Powered by Kunena Forum