Welcome, Guest
Username: Password: Remember me

TOPIC:

1983 ZN1300 Street build. 8 years 8 months ago #8453

  • Nick89
  • Nick89's Avatar Topic Author
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 26
  • Thank you received: 0

Phil wrote: I don't see how fitting pod filters will hurt the fuel injected bikes, although the DFI system won't compensate for it. You can always fit an adjustable fuel pressure regulator to compensate anyway ;)


I actually have an aftermarket adjustable fuel pressure regulator and fuel pump. So this is good news!

Please Log in or Create an account to join the conversation.

1983 ZN1300 Street build. 8 years 8 months ago #8588

  • Nick89
  • Nick89's Avatar Topic Author
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 26
  • Thank you received: 0
Update.

Electrical all put together but I'm not getting any spark and no power to the fuel pump. Yay 32 year old wiring.

Now I got about 20 connections to test and this zn1300 harness has a ton of unused wiring now that all the extra bs is gone.

Anyone have a 1983-84 Kz1300 or Z1300 harness that had the DFI fuel injection?

Please Log in or Create an account to join the conversation.

1983 ZN1300 Street build. 8 years 8 months ago #8589

  • Nick89
  • Nick89's Avatar Topic Author
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 26
  • Thank you received: 0
Systems removed:

Trip/fuel eco computer.

Compass computer.

Air ride pump and system.

Sound, Stereo system.

Accessory lights.

Did the trip/ fuel economy computer have anything to do with the ignition or fuel system? I didn't think it did.

Please Log in or Create an account to join the conversation.

1983 ZN1300 Street build. 8 years 8 months ago #8714

  • aus_z1300
  • aus_z1300's Avatar
  • Offline
  • Elite Member
  • Elite Member
  • Posts: 196
  • Thank you received: 21
An adjustable fuel reg might be an ok dodgy fix for a drag car or bike running full throttle for 10 seconds or so but don't think for a second it is going to sort out the fuel mixtures for you they will be all over the shop.

Please Log in or Create an account to join the conversation.

1983 ZN1300 Street build. 8 years 7 months ago #8871

  • Nick89
  • Nick89's Avatar Topic Author
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 26
  • Thank you received: 0
So far the stock wiring harness is trash. Most of it is dry rotted.

Looks like I'm going to have to wire up a complete custom harness. I can get a Mega squirt to replace the stock ECU, because I'm not even sure if it still works. Or I can get a set of carbs.

Carbs would be less wiring and trying to program the mega squirt.

But its very hard to find KZ1300 carbs.

I was thinking of using three GS500 carbs with custom brackets. Each cylinder is 216cc and the GS carbs are used for 243cc cylinders. It should work.

Please Log in or Create an account to join the conversation.

Last edit: by Nick89.

1983 ZN1300 Street build. 8 years 7 months ago #8890

  • Phil
  • Phil's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • 1984 ZG1300-A1 DFI
  • Posts: 473
  • Thank you received: 144

aus_z1300 wrote: An adjustable fuel reg might be an ok dodgy fix for a drag car or bike running full throttle for 10 seconds or so but don't think for a second it is going to sort out the fuel mixtures for you they will be all over the shop.

It sorted mine, as verified by an exhaust gas analyser at the local bike dyno. The fuelling was pretty consistent across the board :-) You also have to ask if adjustable fuel pressure regulators weren't a fix then why does such a huge aftermarket for them exist in the car world?
Only dead fish go with the flow
The following user(s) said Thank You: Nick89

Please Log in or Create an account to join the conversation.

Time to create page: 0.087 seconds
Powered by Kunena Forum